Promocje
SEB MINI REST X NEW 2020!
SEB MINI REST X NEW 2020!

7 000,00 zł

Cena regularna: 7 500,00 zł

5-42X56mm FFP High Master WA
5-42X56mm FFP High Master WA

18 500,00 zł

Cena regularna: 22 400,00 zł

Karabinek HK SP5 kal. 9x19mm
Karabinek HK SP5 kal. 9x19mm

12 500,00 zł

Cena regularna: 13 500,00 zł

szt.
Karabin HK MR308 20" cal. 308 Win
Karabin HK MR308 20" cal. 308 Win

15 000,00 zł

Cena regularna: 16 899,00 zł

szt.
Terrapin X Range Finder
Terrapin X Range Finder

8 999,00 zł

Cena regularna: 10 000,00 zł

szt.
GENESIS 6x-60x56 FFP
GENESIS 6x-60x56 FFP

33 000,00 zł

Cena regularna: 37 000,00 zł

Karabinek HK SP5K kal. 9x19mm składana kolba
Karabinek HK SP5K kal. 9x19mm składana kolba

12 500,00 zł

Cena regularna: 13 500,00 zł

szt.
Nowości
SAC FINAL SCOPE LEVEL
SAC FINAL SCOPE LEVEL

1 100,00 zł

szt.
SAC MODULAR ACTION WRENCH – BODY ONLY
SAC MODULAR ACTION WRENCH – BODY ONLY

700,00 zł

szt.
Osada MDT ACC ELITE Rem 700 SA - czarna
Osada MDT ACC ELITE Rem 700 SA - czarna

9 500,00 zł

V4 AutoTrickler for A&D

Dostępność: brak towaru
Cena: 3 680,00 zł 3680.00
ilość szt.

towar niedostępny

dodaj do przechowalni

Opis

AutoTrickler V4

Since the original AutoTrickler was invented in 2016, it has become the go-to solution for long range shooters who need to measure accurate powder charges quickly.

 

While the core concept of precisely dispensing onto a lab quality balance has never changed, the mechanical design has constantly improved with two versions of the AutoThrow, Bluetooth support, any many part revisions as a result of new ideas, new processes, and user feedback.

 

AutoTrickler V4 is a clean slate redesign. Starting with the idea of a single assembly without needing manual adjustments, we looked at every part, every feature, every detail, and built exactly what the AutoTrickler should be.

 
  • Works with fine ball powders like CFE223 and H335
  • Works with large kernel powders like N570 and H50BMG
  • Maximum flow rate ~50 GN/s for large caliber rifle
  • Integrated electronics and motors with fixed cabling
  • Acrylic panel and silicone pads ensure assembly is stable, quiet, and level
  • All commonly replaced wear parts from previous versions no longer exist
  • Potential for performance improvements through app updates
  • Integrates with standard A&D FX or FZ 120i, 200i, 300i, or 500i
Inspired by an auger (and refined through simulation, testing, and iteration), a large tube with deep spiral grooves pours bulk powder at rates up to 50 GN/s, ramping down smoothly to within 1-2 grains of the target.
 
A smaller tube then takes over to complete the charge within a kernel using an efficient ramping curve that takes calibrated flow rates into account.
 
By popular request, a green light shines down through the clear panel indicating the correct charge weight has been reached.
 
Both tubes are driven directly by toothed timing belts which will not wear out over time.

The AutoTrickler rests on a clear acrylic panel with soft silicone pads that minimize vibration and noise. The housing can be easily lifted from the panel without disturbing the scale. Silicone pads added to the scale platform keep the entire assembly stable and level.

 

A tilt adjustment within the housing will be factory set. Leveling the scale using its built-in bubble level will set the AutoTrickler at the correct tilt angle.

 

A speed setting within the Bluetooth app will allow a tradeoff between speed and precision based on user preference. Firmware configurability through the app will allow performance options to improve through software updates in the future.

The electronics module fits inside the housing and is replaceable if necessary. The motors are integrated so their short cables will never move or break.
 
One cable connects the AutoTrickler to the FX-120i scale with 20 AWG wiring. Both ends are protected with strain relief and an in-line connector allows easy disconnection. The scale side of the cable can also be replaced separately from the rest of the electronics if needed.

The hopper incorporates a rotating valve so it can be removed easily. The hopper has a flat bottom so it can rest on a table while holding powder.

 

When in use, the hopper is positively locked into the housing. The hopper also blocks the powder reservoir from opening while the valve is open, so the potential for a spill is low.

 

To empty powder, first turn and remove the hopper. Then slide up the window and pour the powder into the hopper. Tilt the unit backwards to clear powder out of the tubes. Any remaining powder will be clearly visible either in the rear reservoir or by looking through the tubes.

 

AutoTrickler V4 includes:

  • V4 AutoTrickler assembly
  • Hopper and cover (will be white, not black like the photo)
  • Clear acrylic panel (not shown in photo)
  • Silicone pads to stabilize the A&D scale platform
  • Glass cup with handle, and tray to position cup on scale
  • Instructions (not yet written)

The scale itself is not included. You can buy it here: https://proshooting.shoplo.com/a-d-fx-120i-grain-balance-1880-x-0-02gn

A&D FX (and FZ) 120i / 200i / 300i / 500i are supported standard. The AutoTrickler electronics will fit into the expansion port in the rear of the A&D scale, are powered through the serial data connector on the scale, and the AutoThrow will mount directly to the top panel included with the scale.

 

UWAGA!!! Cena nie obejmuje wagi widocznej na zdjęciu.

Wagę można kupić tu: https://proshooting.shoplo.com...

 

Opinie o produkcie (0)

do góry
Sklep jest w trybie podglądu
Pokaż pełną wersję strony
Sklep internetowy Shoper.pl